/* plx9080.h * * I modified this file from the plx9060.h header for the * wanXL device driver in the linux kernel, * for the register offsets and bit definitions. Minor modifications, * added plx9080 registers and * stripped out stuff that was specifically for the wanXL driver. I * use this for the plx9080 chip used in the cards supported by * the cb_pcidas64.c driver. * Frank Mori Hess ******************************************************************** * * SBE wanXL device driver * Copyright (C) 1999 RG Studio s.c., http://www.rgstudio.com.pl/ * Written by Krzysztof Halasa * * Portions (C) SBE Inc., used by permission. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ #ifndef __COMEDI_PLX9080_H #define __COMEDI_PLX9080_H // descriptor block used for chained dma transfers struct plx_dma_desc { u32 pci_start_addr; u32 local_start_addr; // transfer_size is in bytes, only first 23 bits of register are used u32 transfer_size; /* address of next descriptor (quad word aligned), plus some * additional bits (see PLX_DMA0_DESCRIPTOR_REG) */ u32 next; }; /********************************************************************** ** Register Offsets and Bit Definitions ** ** Note: All offsets zero relative. IE. Some standard base address ** must be added to the Register Number to properly access the register. ** **********************************************************************/ #define PLX_LAS0RNG_REG 0x0000 /* L, Local Addr Space 0 Range Register */ #define PLX_LAS1RNG_REG 0x00f0 /* L, Local Addr Space 1 Range Register */ #define LRNG_IO 0x00000001 /* Map to: 1=I/O, 0=Mem */ #define LRNG_ANY32 0x00000000 /* Locate anywhere in 32 bit */ #define LRNG_LT1MB 0x00000002 /* Locate in 1st meg */ #define LRNG_ANY64 0x00000004 /* Locate anywhere in 64 bit */ #define LRNG_MEM_MASK 0xfffffff0 // bits that specify range for memory io #define LRNG_IO_MASK 0xfffffffa // bits that specify range for normal io #define PLX_LAS0MAP_REG 0x0004 /* L, Local Addr Space 0 Remap Register */ #define PLX_LAS1MAP_REG 0x00f4 /* L, Local Addr Space 1 Remap Register */ #define LMAP_EN 0x00000001 /* Enable slave decode */ #define LMAP_MEM_MASK 0xfffffff0 // bits that specify decode for memory io #define LMAP_IO_MASK 0xfffffffa // bits that specify decode bits for normal io /* Note: The Local Arbitration Register is only present on the 9060ES part. ** The 9060 part with DMA does not have this register */ #define PLX_LCLARB_REG 0x0008 /* L, Local Arbitration Register */ #define LARB_LLT 0x0000000F /* Local Bus Latency Timer */ #define LARB_LPT 0x000000F0 /* Local Bus Pause Timer */ #define LARB_LTEN 0x00000100 /* Latency Timer Enable */ #define LARB_LPEN 0x00000200 /* Pause Timer Enable */ #define LARB_BREQ 0x00000400 /* Local Bus BREQ Enable */ /* Note: The Expansion ROM stuff is only relevant to the PC environment. ** This expansion ROM code is executed by the host CPU at boot time. ** For this reason no bit definitions are provided here. */ #define PLX_ROMRNG_REG 0x0010 /* L, Expn ROM Space Range Register */ #define PLX_ROMMAP_REG 0x0014 /* L, Local Addr Space Range Register */ #define PLX_REGION_REG 0x0018 /* L, Local Bus Region Descriptor */ #define RGN_WIDTH 0x00000002 /* Local bus width bits */ #define RGN_8BITS 0x00000000 /* 08 bit Local Bus */ #define RGN_16BITS 0x00000001 /* 16 bit Local Bus */ #define RGN_32BITS 0x00000002 /* 32 bit Local Bus */ #define RGN_MWS 0x0000003C /* Memory Access Wait States */ #define RGN_0MWS 0x00000000 #define RGN_1MWS 0x00000004 #define RGN_2MWS 0x00000008 #define RGN_3MWS 0x0000000C #define RGN_4MWS 0x00000010 #define RGN_6MWS 0x00000018 #define RGN_8MWS 0x00000020 #define RGN_MRE 0x00000040 /* Memory Space Ready Input Enable */ #define RGN_MBE 0x00000080 /* Memory Space Bterm Input Enable */ #define RGN_RWS 0x003C0000 /* Expn ROM Wait States */ #define RGN_RRE 0x00400000 /* ROM Space Ready Input Enable */ #define RGN_RBE 0x00800000 /* ROM Space Bterm Input Enable */ #define RGN_MBEN 0x01000000 /* Memory Space Burst Enable */ #define RGN_RBEN 0x04000000 /* ROM Space Burst Enable */ #define RGN_THROT 0x08000000 /* De-assert TRDY when FIFO full */ #define RGN_TRD 0xF0000000 /* Target Ready Delay /8 */ #define PLX_DMRNG_REG 0x001C /* L, Direct Master Range Register */ #define PLX_LBAPMEM_REG 0x0020 /* L, Lcl Base Addr for PCI mem space */ #define PLX_LBAPIO_REG 0x0024 /* L, Lcl Base Addr for PCI I/O space */ #define PLX_DMMAP_REG 0x0028 /* L, Direct Master Remap Register */ #define DMM_MAE 0x00000001 /* Direct Mstr Memory Acc Enable */ #define DMM_IAE 0x00000002 /* Direct Mstr I/O Acc Enable */ #define DMM_LCK 0x00000004 /* LOCK Input Enable */ #define DMM_PF4 0x00000008 /* Prefetch 4 Mode Enable */ #define DMM_THROT 0x00000010 /* Assert IRDY when read FIFO full */ #define DMM_PAF0 0x00000000 /* Programmable Almost fill level */ #define DMM_PAF1 0x00000020 /* Programmable Almost fill level */ #define DMM_PAF2 0x00000040 /* Programmable Almost fill level */ #define DMM_PAF3 0x00000060 /* Programmable Almost fill level */ #define DMM_PAF4 0x00000080 /* Programmable Almost fill level */ #define DMM_PAF5 0x000000A0 /* Programmable Almost fill level */ #define DMM_PAF6 0x000000C0 /* Programmable Almost fill level */ #define DMM_PAF7 0x000000D0 /* Programmable Almost fill level */ #define DMM_MAP 0xFFFF0000 /* Remap Address Bits */ #define PLX_CAR_REG 0x002C /* L, Configuration Address Register */ #define CAR_CT0 0x00000000 /* Config Type 0 */ #define CAR_CT1 0x00000001 /* Config Type 1 */ #define CAR_REG 0x000000FC /* Register Number Bits */ #define CAR_FUN 0x00000700 /* Function Number Bits */ #define CAR_DEV 0x0000F800 /* Device Number Bits */ #define CAR_BUS 0x00FF0000 /* Bus Number Bits */ #define CAR_CFG 0x80000000 /* Config Spc Access Enable */ #define PLX_DBR_IN_REG 0x0060 /* L, PCI to Local Doorbell Register */ #define PLX_DBR_OUT_REG 0x0064 /* L, Local to PCI Doorbell Register */ #define PLX_INTRCS_REG 0x0068 /* L, Interrupt Control/Status Reg */ #define ICS_AERR 0x00000001 /* Assert LSERR on ABORT */ #define ICS_PERR 0x00000002 /* Assert LSERR on Parity Error */ #define ICS_SERR 0x00000004 /* Generate PCI SERR# */ #define ICS_MBIE 0x00000008 // mailbox interrupt enable #define ICS_PIE 0x00000100 /* PCI Interrupt Enable */ #define ICS_PDIE 0x00000200 /* PCI Doorbell Interrupt Enable */ #define ICS_PAIE 0x00000400 /* PCI Abort Interrupt Enable */ #define ICS_PLIE 0x00000800 /* PCI Local Int Enable */ #define ICS_RAE 0x00001000 /* Retry Abort Enable */ #define ICS_PDIA 0x00002000 /* PCI Doorbell Interrupt Active */ #define ICS_PAIA 0x00004000 /* PCI Abort Interrupt Active */ #define ICS_LIA 0x00008000 /* Local Interrupt Active */ #define ICS_LIE 0x00010000 /* Local Interrupt Enable */ #define ICS_LDIE 0x00020000 /* Local Doorbell Int Enable */ #define ICS_DMA0_E 0x00040000 /* DMA #0 Interrupt Enable */ #define ICS_DMA1_E 0x00080000 /* DMA #1 Interrupt Enable */ #define ICS_LDIA 0x00100000 /* Local Doorbell Int Active */ #define ICS_DMA0_A 0x00200000 /* DMA #0 Interrupt Active */ #define ICS_DMA1_A 0x00400000 /* DMA #1 Interrupt Active */ #define ICS_BIA 0x00800000 /* BIST Interrupt Active */ #define ICS_TA_DM 0x01000000 /* Target Abort - Direct Master */ #define ICS_TA_DMA0 0x02000000 /* Target Abort - DMA #0 */ #define ICS_TA_DMA1 0x04000000 /* Target Abort - DMA #1 */ #define ICS_TA_RA 0x08000000 /* Target Abort - Retry Timeout */ #define ICS_MBIA(x) (0x10000000 << ((x) & 0x3)) // mailbox x is active #define PLX_CONTROL_REG 0x006C /* L, EEPROM Cntl & PCI Cmd Codes */ #define CTL_RDMA 0x0000000E /* DMA Read Command */ #define CTL_WDMA 0x00000070 /* DMA Write Command */ #define CTL_RMEM 0x00000600 /* Memory Read Command */ #define CTL_WMEM 0x00007000 /* Memory Write Command */ #define CTL_USERO 0x00010000 /* USERO output pin control bit */ #define CTL_USERI 0x00020000 /* USERI input pin bit */ #define CTL_EE_CLK 0x01000000 /* EEPROM Clock line */ #define CTL_EE_CS 0x02000000 /* EEPROM Chip Select */ #define CTL_EE_W 0x04000000 /* EEPROM Write bit */ #define CTL_EE_R 0x08000000 /* EEPROM Read bit */ #define CTL_EECHK 0x10000000 /* EEPROM Present bit */ #define CTL_EERLD 0x20000000 /* EEPROM Reload Register */ #define CTL_RESET 0x40000000 /* !! Adapter Reset !! */ #define CTL_READY 0x80000000 /* Local Init Done */ #define PLX_ID_REG 0x70 // hard-coded plx vendor and device ids #define PLX_REVISION_REG 0x74 // silicon revision #define PLX_DMA0_MODE_REG 0x80 // dma channel 0 mode register #define PLX_DMA1_MODE_REG 0x94 // dma channel 0 mode register #define PLX_LOCAL_BUS_16_WIDE_BITS 0x1 #define PLX_LOCAL_BUS_32_WIDE_BITS 0x3 #define PLX_LOCAL_BUS_WIDTH_MASK 0x3 #define PLX_DMA_EN_READYIN_BIT 0x40 // enable ready in input #define PLX_EN_BTERM_BIT 0x80 // enable BTERM# input #define PLX_DMA_LOCAL_BURST_EN_BIT 0x100 // enable local burst mode #define PLX_EN_CHAIN_BIT 0x200 // enables chaining #define PLX_EN_DMA_DONE_INTR_BIT 0x400 // enables interrupt on dma done #define PLX_LOCAL_ADDR_CONST_BIT 0x800 // hold local address constant (don't increment) #define PLX_DEMAND_MODE_BIT 0x1000 // enables demand-mode for dma transfer #define PLX_DMA_INTR_PCI_BIT 0x20000 // routes dma interrupt to pci bus (instead of local bus) #define PLX_DMA0_PCI_ADDRESS_REG 0x84 // pci address that dma transfers start at #define PLX_DMA1_PCI_ADDRESS_REG 0x98 #define PLX_DMA0_LOCAL_ADDRESS_REG 0x88 // local address that dma transfers start at #define PLX_DMA1_LOCAL_ADDRESS_REG 0x9c #define PLX_DMA0_TRANSFER_SIZE_REG 0x8c // number of bytes to transfer (first 23 bits) #define PLX_DMA1_TRANSFER_SIZE_REG 0xa0 #define PLX_DMA0_DESCRIPTOR_REG 0x90 // descriptor pointer register #define PLX_DMA1_DESCRIPTOR_REG 0xa4 #define PLX_DESC_IN_PCI_BIT 0x1 // descriptor is located in pci space (not local space) #define PLX_END_OF_CHAIN_BIT 0x2 // end of chain bit #define PLX_INTR_TERM_COUNT 0x4 // interrupt when this descriptor's transfer is finished #define PLX_XFER_LOCAL_TO_PCI 0x8 // transfer from local to pci bus (not pci to local) #define PLX_DMA0_CS_REG 0xa8 // command status register #define PLX_DMA1_CS_REG 0xa9 #define PLX_DMA_EN_BIT 0x1 // enable dma channel #define PLX_DMA_START_BIT 0x2 // start dma transfer #define PLX_DMA_ABORT_BIT 0x4 // abort dma transfer #define PLX_CLEAR_DMA_INTR_BIT 0x8 // clear dma interrupt #define PLX_DMA_DONE_BIT 0x10 // transfer done status bit #define PLX_DMA0_THRESHOLD_REG 0xb0 // command status register /* * Accesses near the end of memory can cause the PLX chip * to pre-fetch data off of end-of-ram. Limit the size of * memory so host-side accesses cannot occur. */ #define PLX_PREFETCH 32 /* * The PCI Interface, via the PCI-9060 Chip, has up to eight (8) Mailbox * Registers. The PUTS (Power-Up Test Suite) handles the board-side * interface/interaction using the first 4 registers. Specifications for * the use of the full PUTS' command and status interface is contained * within a separate SBE PUTS Manual. The Host-Side Device Driver only * uses a subset of the full PUTS interface. */ /*****************************************/ /*** MAILBOX #(-1) - MEM ACCESS STS ***/ /*****************************************/ #define MBX_STS_VALID 0x57584744 /* 'WXGD' */ #define MBX_STS_DILAV 0x44475857 /* swapped = 'DGXW' */ /*****************************************/ /*** MAILBOX #0 - PUTS STATUS ***/ /*****************************************/ #define MBX_STS_MASK 0x000000ff /* PUTS Status Register bits */ #define MBX_STS_TMASK 0x0000000f /* register bits for TEST number */ #define MBX_STS_PCIRESET 0x00000100 /* Host issued PCI reset request */ #define MBX_STS_BUSY 0x00000080 /* PUTS is in progress */ #define MBX_STS_ERROR 0x00000040 /* PUTS has failed */ #define MBX_STS_RESERVED 0x000000c0 /* Undefined -> status in transition. We are in process of changing bits; we SET Error bit before RESET of Busy bit */ #define MBX_RESERVED_5 0x00000020 /* FYI: reserved/unused bit */ #define MBX_RESERVED_4 0x00000010 /* FYI: reserved/unused bit */ /******************************************/ /*** MAILBOX #1 - PUTS COMMANDS ***/ /******************************************/ /* * Any attempt to execute an unimplement command results in the PUTS * interface executing a NOOP and continuing as if the offending command * completed normally. Note: this supplies a simple method to interrogate * mailbox command processing functionality. */ #define MBX_CMD_MASK 0xffff0000 /* PUTS Command Register bits */ #define MBX_CMD_ABORTJ 0x85000000 /* abort and jump */ #define MBX_CMD_RESETP 0x86000000 /* reset and pause at start */ #define MBX_CMD_PAUSE 0x87000000 /* pause immediately */ #define MBX_CMD_PAUSEC 0x88000000 /* pause on completion */ #define MBX_CMD_RESUME 0x89000000 /* resume operation */ #define MBX_CMD_STEP 0x8a000000 /* single step tests */ #define MBX_CMD_BSWAP 0x8c000000 /* identify byte swap scheme */ #define MBX_CMD_BSWAP_0 0x8c000000 /* use scheme 0 */ #define MBX_CMD_BSWAP_1 0x8c000001 /* use scheme 1 */ #define MBX_CMD_SETHMS 0x8d000000 /* setup host memory access window size */ #define MBX_CMD_SETHBA 0x8e000000 /* setup host memory access base address */ #define MBX_CMD_MGO 0x8f000000 /* perform memory setup and continue (IE. Done) */ #define MBX_CMD_NOOP 0xFF000000 /* dummy, illegal command */ /*****************************************/ /*** MAILBOX #2 - MEMORY SIZE ***/ /*****************************************/ #define MBX_MEMSZ_MASK 0xffff0000 /* PUTS Memory Size Register bits */ #define MBX_MEMSZ_128KB 0x00020000 /* 128 kilobyte board */ #define MBX_MEMSZ_256KB 0x00040000 /* 256 kilobyte board */ #define MBX_MEMSZ_512KB 0x00080000 /* 512 kilobyte board */ #define MBX_MEMSZ_1MB 0x00100000 /* 1 megabyte board */ #define MBX_MEMSZ_2MB 0x00200000 /* 2 megabyte board */ #define MBX_MEMSZ_4MB 0x00400000 /* 4 megabyte board */ #define MBX_MEMSZ_8MB 0x00800000 /* 8 megabyte board */ #define MBX_MEMSZ_16MB 0x01000000 /* 16 megabyte board */ /***************************************/ /*** MAILBOX #2 - BOARD TYPE ***/ /***************************************/ #define MBX_BTYPE_MASK 0x0000ffff /* PUTS Board Type Register */ #define MBX_BTYPE_FAMILY_MASK 0x0000ff00 /* PUTS Board Family Register */ #define MBX_BTYPE_SUBTYPE_MASK 0x000000ff /* PUTS Board Subtype */ #define MBX_BTYPE_PLX9060 0x00000100 /* PLX family type */ #define MBX_BTYPE_PLX9080 0x00000300 /* PLX wanXL100s family type */ #define MBX_BTYPE_WANXL_4 0x00000104 /* wanXL400, 4-port */ #define MBX_BTYPE_WANXL_2 0x00000102 /* wanXL200, 2-port */ #define MBX_BTYPE_WANXL_1s 0x00000301 /* wanXL100s, 1-port */ #define MBX_BTYPE_WANXL_1t 0x00000401 /* wanXL100T1, 1-port */ /*****************************************/ /*** MAILBOX #3 - SHMQ MAILBOX ***/ /*****************************************/ #define MBX_SMBX_MASK 0x000000ff /* PUTS SHMQ Mailbox bits */ /***************************************/ /*** GENERIC HOST-SIDE DRIVER ***/ /***************************************/ #define MBX_ERR 0 #define MBX_OK 1 /* mailbox check routine - type of testing */ #define MBXCHK_STS 0x00 /* check for PUTS status */ #define MBXCHK_NOWAIT 0x01 /* dont care about PUTS status */ /* system allocates this many bytes for address mapping mailbox space */ #define MBX_ADDR_SPACE_360 0x80 /* wanXL100s/200/400 */ #define MBX_ADDR_MASK_360 (MBX_ADDR_SPACE_360-1) #endif /* __COMEDI_PLX9080_H */